Manitowoc, WI & the Lakeshore Mon – Sat · Leak Calls 7 Days a Week
Home › Blog › Cost Guide
Cost Guide

What Does Flat Roof Replacement Cost in Manitowoc, WI?

Ask what a flat roof costs and you'll hear anything from a few dollars a square foot to well over twenty. Both can be honest. The number depends on the membrane, what's under the old roof, and how much insulation, drainage and edge work the new roof needs. Here are typical 2026 ranges for Manitowoc and the lakeshore, what moves them, and how to compare bids fairly.

Typical flat roof costs on the lakeshore

For a number on your own building, try the free flat and commercial roof cost calculator. It uses the same ranges as this table.

These are typical installed costs per square foot for low-slope roofs, including membrane, insulation, standard flashings and edge metal. Size, height, access and condition set the exact figure, which is why a real quote comes after someone has walked the roof and taken a core.

SystemTypical installed costNotes
EPDM (black rubber)$5.50 – $11 / sq ftProven in cold weather; stays flexible below zero
TPO (white single-ply)$6 – $12 / sq ftHeat-welded seams; reflective; very common on new roofs
PVC (single-ply)$7 – $14 / sq ftResists grease and chemicals; food plants and restaurants
Modified bitumen$5 – $10 / sq ftMulti-ply, tough underfoot; storefronts and small roofs
Recover over existing roof$4 – $8 / sq ftOnly over a single, dry layer on a sound deck
Silicone or acrylic coating$2 – $5 / sq ftRestoration, not replacement; dry insulation required
Small residential flat roof$2,500 – $7,000 per jobPorch, addition or garage; higher per sq ft

Roof leaking right now?

Manitowoc Superior Flat Roofing repairs, coats and replaces commercial and flat roofs across Manitowoc County and the lakeshore, with a written price before any work starts. Request a quote online and we’ll call you back.

What changes the price

What's underneath

Tear-off is a big share of the labor. A single dry roof on a good deck can often be recovered instead. A wet roof, or one that already has a recover on it, comes off down to the deck. Core cuts settle it before the quote. More in recover vs. replacement.

Wet insulation and deck repairs

Years of small leaks leave wet insulation and sometimes rusted steel or rotted wood deck. All of it gets replaced, and a moisture survey up front keeps it from turning into a change order in the middle of the job.

Wind exposure at the edges

Buildings near the lake, or standing alone in open ground, take higher wind loads at their corners and perimeter. The roof design accounts for that with tighter fastening in those zones and tested edge metal. It costs a little more and it is the part of the roof that most often fails when it is skimped on. See wind damage on lakeshore flat roofs.

Insulation and energy code

Replacing a roof usually triggers today's insulation requirements, which are far thicker than what went on decades ago. More insulation means taller edges and curbs, and sometimes raised rooftop units. It also lowers heating bills and reduces the heat loss that melts snow and feeds ice at the drains.

Drainage

If the old roof ponded, the new one shouldn't. Tapered insulation, crickets and extra drains add cost now and add years to the new roof. See ponding water on a flat roof.

Rooftop equipment and access

Every unit, vent, pipe, skylight and hatch needs its own flashing. A plain warehouse roof is cheaper per square foot than a smaller roof full of equipment. Height, crane days and dumpster placement matter too.

How to line up bids that don't match

  • Same scope: tear-off or recover, insulation thickness, new flashings at every wall and curb, and the same edge metal.
  • Wet insulation: is there an allowance or a unit price, or nothing at all? Nothing tends to become a change order.
  • Membrane and attachment: thickness, fully adhered or fastened, and how corners and edges are secured.
  • Warranty: contractor workmanship, manufacturer material-only, or a full system warranty. They aren't the same thing.
  • Permits on homes: in Wisconsin, a contractor who takes out a permit for a one- or two-family home must hold the state's Dwelling Contractor credential.

Why small roofs cost more per square foot

Setup, edge metal and the flashing into the house cost about the same on a 200 square foot porch as on a 2,000 square foot addition. On small roofs those fixed costs dominate. They're also exactly what makes a small flat roof stop leaking, so they're the wrong place to save. See residential flat roof replacement.


More roofing guides

Questions & Answers

Frequently asked questions

Most commercial single-ply replacements land around $6–$13 per square foot installed, with insulation and flashings. A recover over an existing roof is often $4–$8. Small flat roofs on houses cost more per square foot because edges and wall flashing make up more of the job.

For planning, roughly $60,000–$130,000 for a full tear-off and new single-ply roof, depending on the membrane, the insulation required, deck repairs and the number of rooftop units and penetrations. A recover on a qualifying roof can cost well under that.

Often about $2,500–$7,000, depending on size, access, material and how much rotted decking needs replacing.

Sometimes a little. Buildings exposed to wind off Lake Michigan may need more fasteners at corners and edges, or heavier edge metal, to meet the wind design. It is a small share of the total and it is what keeps the roof on.

Usually: most coatings run about $2–$5 per square foot. But a coating only works if the insulation underneath is dry. See are roof coatings worth it?

Roof leaking?

Leak repair, coatings and replacement for commercial and flat roofs across Manitowoc County and the lakeshore. Tell us about the roof. You get a written price before any work starts.

Request a Quote